![]() This thing has CHANGED THE WAY I THINK ABOUT MITERS. and then I was looking through the gift basket I won in a Kreg giveaway and it was as if my guardian angel (or should I say “guardian angle”) was watching out for me. I just couldn’t use any of those tutorials for this project. your head will EXPLODE) or they didn’t even mention odd angles since they assumed you only had 90 degree corners. I scoured the internet for good tutorials on how to miter crown and they either required you to just “guess” the angle (and use a pizza box?!), or they had all sorts of math I knew I would screw up (no seriously. Here is what that sucker looks like up close.I knew I would eventually install crown up there so I didn’t even paint! (*blushes*) and if you look close you can see I never finished off the top of the corner cabinet (the strange crop wasn't an accident! #keepingitrealwithkimsix): Here is the before and after of the bathroom vanity. And it was so easy, I had to share the secret with you. But thanks to Kreg** I finally figure out how to do it. That 6 foot piece of molding has been leaning against the bedroom wall for TWO FULL YEARS (#keepingitrealwithkimsix). I was paralyzed with fear of screwing it up. And I only had EXACTLY 6 feet of matching crown from the cabinet company. I was having a hard time figuring out how to miter the crown at the funky angles resulting from the weird cabinet shape. you probably forgot about that since it was TWO YEARS AGO. Remember when I redid my master bathroom and I installed a corner cabinet on the vanity? Remember I said I was going to install crown molding on that cabinet to finish the room? Yeah. Then bring views of those moldings as a detail thing in your LayOut document.I have a confession to make. Those could be premade components in which you extrude the molding profile around a single corner. Then create molding “samples” to show the client. ![]() That also makes it easy to swap between moldings once you have them all modeled.ĭepending on the way you show the interior views in your model, you might find it works well enough to have sort of generic moldings for the wider views. It’s also handy when you want to run base molding and crown molding around the same path.Īnd yes, of course create a group or component of the extrude molding and give it a layer to control its visibility. ![]() By placing the path for the extrusion so it isn’t in contact with the profile, the path doesn’t get consumed during Follow Me which makes it available for future use. So instead of my component just being a cross section, it now updates to a whole big shape of the trim piece.Īm I on the right track and just missing an easy step, or totally off base and there’s a better way to do this? Any and all help is very much appreciated!īonus question: while using the follow-me tool, is there any way to set it to return the ends of the profile at certain locations? My only idea was to make sure on my guide line, I had a tiny 90 degree line coming off the end which would cause the tool to turn the profile along the tiny/invisible “corner” I had created.īut the better method is to extrude each profile option one at a time, grouping each individual instance together and either show/hiding or setting to a visible/invisible layer as necessary. My main issue is that I can’t figure out how to get the face of the component to follow-me along the path I’ve drawn within the house model, without the component itself updating to fit the shape of whatever I’ just extruded it along. Once I had done this, I was hoping I could just replace the component within the model to another cross section component to update the profile of the trim all at once. the bottom back corner for all baseboard cross sections), then apply the component to the model and use the follow-me tool to extrude the profile along the areas I wanted the trim. My (unsuccessful) strategy was to set each of my trim profile cross sections as individual components, setting the component’s axis to a common point (e.g. What is the best way to organize my model so that I can easily update baseboard, crown, and wall molding profiles to different options during the design phase? For example, in the house model I have, I would like to be able to quickly update all of the trim profiles in a room to show different options of finishes, different heights of baseboards, different profiles of crown, etc. A search of the forum and internet did not produce a solution for me, even though I’m sure I’m missing it.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |